Gas Safe and OFTEC registered engineers finding and fixing faults on gas, oil and LPG boilers. We repair first, and only suggest a new boiler when a repair no longer makes sense.
Our Services
Boiler Repairs

About This Service
Getting your heating and hot water back on
When your boiler stops working, you want the fault found properly and fixed safely. Heatfire carries out fault-finding and repairs on domestic and commercial gas, oil and LPG boilers. Our Gas Safe, OFTEC and Unvented-registered engineers prioritise repairing components and controls where practical, and clearly explain replacement options when required.
We're boiler repair engineers based in Willenhall, serving Walsall, Wolverhampton, Cannock and the surrounding area. With over 15 years' local experience we provide honest advice, rapid diagnosis and work to current safety standards.
Common boiler faults we fix include:
- No hot water while the heating still works, often a sticking diverter valve on a combi boiler
- Pressure that keeps dropping, from a small leak, a faulty pressure relief valve or a failed expansion vessel
- A blocked or frozen condensate pipe, a common cause of breakdowns in a cold snap
- A boiler that won't light or keeps cutting out, from ignition, gas valve or flame sensing faults
- A fault code or flashing light on the display
- Water leaking from the boiler or the pipework underneath it
- Banging, gurgling or kettling noises, often from limescale, sludge or air in the system
- Cold radiators or heating that won't come on, from a failed pump, circuit board or controls
A fault code tells you which part of the boiler has stopped it working, not always why. Note the code and your boiler's make and model before you get in touch, as it helps us arrive with the right parts.
In freezing weather, check the condensate pipe first. It's the plastic pipe that runs from the boiler to a drain outside, and if it freezes the boiler shuts itself down. Our guide to thawing a frozen condensate pipe safely shows you how. Never take the boiler's casing off yourself. Only a registered engineer should work inside a boiler: Gas Safe for gas and LPG, OFTEC for oil.
Our Process
How It Works
Call & Initial Triage
Phone us or use the online form to describe symptoms; we triage urgency, log serial numbers and advise immediate safety steps.
On-site Fault Finding
Engineer arrives with diagnostic kit, runs safety checks and fault-finding on controls, ignition, pumps, valves and wiring to identify the root cause.
Repair, Test & Handover
We repair or replace components where possible, test the system under load, complete safety paperwork and explain the work and any next steps.
REVIEWS
What Our Customers Say
— Petronella Tomkinson
— Ifeoma Ogbonnaya
FAQ
Your boiler repair questions answered
We aim for same-day diagnosis where possible and prioritise emergency faults. Customers on one of our service plans receive priority call-outs; otherwise we book the earliest practical slot and give a clear ETA when you call.
Yes. Our engineers are qualified to work on gas, oil and LPG-fired boilers and are Gas Safe, OFTEC and Unvented registered. That means repairs are carried out to the correct safety standards for each fuel type.
We always attempt a repair first where it is safe and cost-effective. If the fault is recurring, parts are obsolete or the boiler is beyond reliable repair, we'll explain the reasons and present replacement options so you can make an informed decision. If a new boiler is the better choice, our boiler installation service explains what's involved.
Repairs include a workmanship guarantee and any manufacturer part warranties where applicable. We’ll confirm the exact cover for your job before work begins and issue any relevant paperwork on completion.
For a leak, turn off the boiler and isolate the water supply if safe to do so. If a carbon monoxide alarm sounds or you suspect a CO leak, get everyone out of the property and call the National Gas Emergency Service, then us. Don't use any gas appliance until a qualified engineer has checked it.
It depends on what's wrong, so we find the fault before pricing the repair. The main things that affect the cost are which part has failed, how easy that part is to get for your boiler's make and model, and how long the job takes. A sensor or seal usually costs far less than a new pump, fan or circuit board. We explain what we've found and your options before any repair goes ahead.
Book your boiler repair today
Tell us what your boiler is doing and we'll arrange an engineer visit. Prefer a callback? Leave a message and we'll call you back.
Other Services
